鋁合金電梯門套的安裝流程通常包括以下幾個步驟：

　　The installation process of aluminum alloy elevator door frames usually includes the following steps:

　　一、準備工作

　　1、 Preparation work

　　確認材料：確保所需的鋁合金電梯門套材料齊全，包括門套本身、螺絲、角碼、線條、發泡膠、結構膠等安裝所需的配件。

　　Confirm materials: Ensure that the required aluminum alloy elevator door frame materials are complete, including the door frame itself, screws, brackets, lines, foam adhesive, structural adhesive, and other accessories required for installation.

　　準備工具：準備好所需的安裝工具，如電鉆、錘子、電動螺絲刀、水平儀、游標卡尺、靠尺板、方尺等。

　　Preparation tools: Prepare the necessary installation tools, such as drill, hammer, electric screwdriver, level, vernier caliper, ruler plate, square ruler, etc.

　　二、清理與測量

　　2、 Cleaning and measurement

　　清理墻面：在安裝之前，先清理電梯門口的墻面，確保平整干凈，無雜物和灰塵。

　　Cleaning the wall: Before installation, clean the wall at the elevator entrance to ensure it is flat, clean, and free of debris and dust.

　　測量門洞：使用測量工具準確測量門洞的尺寸，確定鋁合金電梯門套的長度和寬度，并將其標記在墻上以便后續安裝。

　　Measurement of door opening: Use measuring tools to accurately measure the size of the door opening, determine the length and width of the aluminum alloy elevator door frame, and mark it on the wall for subsequent installation.

　　三、安裝調節槽與側板

　　3、 Install adjustment slot and side panel

　　安裝調節槽：將調節槽按照預定位置用自攻螺絲固定在電梯門框上。

　　Install adjustment groove: Fix the adjustment groove on the elevator door frame with self tapping screws according to the predetermined position.

　　組裝側板：將后側板兩端插入側板角碼，并用自攻螺絲分離固定。然后組裝左右整套側板模塊，確保側板角碼與平行定位片插入線條槽口內，角度平整緊密。

　　Assemble side panel: Insert the two ends of the rear side panel into the corner code of the side panel and separate and fix them with self tapping screws. Then assemble the entire set of left and right side panel modules, ensuring that the side panel corner codes and parallel positioning pieces are inserted into the groove of the line, with a flat and tight angle.

　　四、打膠與固定

　　4、 Glue application and fixation

　　打膠處理：在左右兩邊調節槽內部打膠，然后將側板模塊插入調節條口內，外面調整與墻面平行。接著用發泡膠填充側板左右兩邊的空隙，線條卡槽內部也打膠處理。

　　Glue treatment: Apply glue inside the adjustment slots on both sides, then insert the side panel module into the adjustment strip opening, and adjust the outside to be parallel to the wall. Then fill the gaps on both sides of the side panel with foam adhesive, and apply glue to the inside of the line slot.

　　扣接線條：將線條與側板外立面后接，確保線條與側板扣接到位，線條的背面與墻面貼實無縫隙。

　　Buckling Line: Connect the line to the outer facade of the side panel, ensuring that the line is securely fastened to the side panel, and the back of the line is firmly attached to the wall without any gaps.

　　五、固定與收尾

　　5、 Fixed and Closing

　　打結構膠：在電梯門框與門套對接處打結構膠，以及門套線條與墻體接觸面打結構膠，確保固定牢固且密封性良好。

　　Apply structural adhesive: Apply structural adhesive to the joint between the elevator door frame and door frame, as well as to the contact surface between the door frame line and the wall, to ensure firm fixation and good sealing.

　　檢查與調整：使用水平儀等工具檢查門套的安裝水平度和垂直度，如有偏差及時調整。

　　Inspection and adjustment: Use tools such as a spirit level to check the installation levelness and verticality of the door frame, and adjust it promptly if there is any deviation.

　　清理現場：安裝完成后，清理現場多余的材料和垃圾，保持環境整潔。

　　Clean up the site: After installation is completed, clean up any excess materials and garbage on site to maintain a clean environment.

　　六、安全與注意事項

　　6、 Safety and Precautions

　　專業安裝：電梯門套的安裝最好由專業的安裝人員進行，遵循相關的安裝規范和操作要求。

　　Professional installation: The installation of elevator door frames is best carried out by professional installers, following relevant installation specifications and operating requirements.

　　安全防護：在安裝過程中，注意佩戴好安全帽、手套等防護用品，確保施工安全。

　　Safety protection: During the installation process, pay attention to wearing protective equipment such as helmets and gloves to ensure construction safety.

　　細節處理：注意處理門套與墻面、地板等接縫處的細節，確保美觀且密封性良好。

　　Detail processing: Pay attention to the details of the joints between the door frame and the wall, floor, etc., to ensure aesthetics and good sealing.

　　綜上所述，鋁合金電梯門套的安裝流程需要細致、耐心和專業的操作技能。遵循正確的安裝步驟和注意事項，可以確保門套的安裝質量和安全性。

　　In summary, the installation process of aluminum alloy elevator door frames requires meticulous, patient, and professional operational skills. Following the correct installation steps and precautions can ensure the installation quality and safety of the door frame.

　　本文由 山東不銹鋼電梯門套 友情奉獻.更多有關的知識請點擊  http://yqzzdz.com.cn   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Shandong Stainless Steel Elevator Door Frame For more related knowledge, please click http://yqzzdz.com.cn Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.